One page was not enough, so welcome to the Second
to show you why I'm so intent on building this cyclone, watch this
Dirty DC!! <- right click, save ask
on the right side the piece of tape over the whole is off again,
but other wise,
you can see the fine dust that gets airborne every time I start up the
Puff the Dirty DC's Imminent
Time to hang the Cyclone
Puff the Dirty DC's former parking space, soon to be occupied by the
Here is the top Freedom Cleat on the wall
Freedom Cleats on the Cyclone (it is upside down in this pic)
Standing on the floor waiting to be hung on the wall.
There it is, hang-em high!
Looks like that light is going to have to find a new home...
There, the light is out of the way, next the extra ducting...........
The ducting is removed, but I've got to rotate the cyclone so the inlet
out a bit more.
Changing to the Cyclone, I've removed just over 13 feet of
and about 4 feet of flex hose, not to mention six 45 elbows.
I'm sure that 2 of those elbows will go back, and maybe half of the flex
All in all I've removed about 1/3 of the total ductwork,
so this should increase the suction for each machine as well.
A top down view
I've got to turn the inlet on an
angle, so it
will easily line up with the existing ducting.
be mounted on the side, and the filter will be below the blower.
OK I had good evening....
I got the inlet rotated, and the side panel on as well
The inlet and the ductwork just about lines up, some "persuasion"
might be needed...
OK Puff is officially gone, RIP....
I need to lose some steel here, sure wish I had a plasma arc torch!!
4" angle grinder, and a little time plus a lot of mess.......
That is looking better!
Going airborne, so we don't need no stinking wheels!
The new and lightened blower!
It still weighs a ton, that 3 phase motor is not easy lifting!
going to have to break down and paint it I guess...
An artists rendition of what will come (Ok I'm a lousy artist)
Cleaned up, floor swept, time for bed....
I needed to clean the blower up to paint it, but I
remove the impeller from the motor, so I could remove the motor.
I had to make a puller to do this, so I did....
Cleaned up, motor removed, and ready for paint
Painted, but no shroud yet.
There, almost as good as new!!
I finished the ducts as well, this is the main duct going into the
Needs caulking and tape.
From the other side, this gives me a fairly straight shot right into the
Bill's pages say the transition should be
well I could not do that, but at least the duct is nearly that long.
On to the mounting Blower
I've decided to mount the blower housing on the side
cyclone, as the 3-phase motor I'm using is really long,
I'd have to make the dust bin on the very bottom of the cyclone really
The blower housing and motor are HEAVY, so I've got to
good bracket to make sure that nothing comes crashing down.
I've decided to use tubing instead of angle iron, as I think it looks
and it will be stronger.
Here is the bracket all welded up...
OK, here is the frame all welded up, all 1" tubing, 45 corners and
all to heck!
Here is the view from the motor area.
I mocked this up to make sure everything fits.
This is the view that you will have when you stand in front of the
The impeller view
OK I put the bracket up on the wall, just one anchor,
as I want to just see how it would all fit.
A front view
Now I put the blower housing up on the bracket, to see if it fits.
Well it does not fit, there is not enough space between the ceiling and
cyclone, just, about 3/4".
I could lower the
there is no need, I'll just move the bracket to the right about 6 or 8
as I'll be using some flex hose to join the cyclone outlet and the
the 3/4" difference will be taken up by the flex hose with ease.
There you go, I put the motor up there just to see if I could do it.
You bet, but I guess all the lifting of cases of beer did some good.
Don't worry, with only one anchor in the wall, the motor was soon taken
now that the paint has dried............mostly.......
You can see the rubber bumper/cushions I put between the bracket and the
Here you can see the blower in relation to the cyclone
The blower just fits, there is about 1 cm of space there...
With the flex hose on, yes a straight shot would have been better, but
Another view of the cyclone to blower flex hose route
As a safety feature I'm going to put this turnbuckle in here to take up
yes it is duct taped to the ceiling at the moment,
I'm just getting the placement of the anchor right.
got things well in hand, and I'm getting really close...
Everything is all caulked and taped up, all the connections are tight,
wiring is finished as well
I don't have the filters
yet, but I
did not want to run the cyclone with out any bags, might burn up the
So I put the puffster back into action!
I need to build the dust bin for the bottom of the cyclone, and then the
bottom pieces for the filter stack.
to page Three, and the final stage!!!